Tuesday, August 10, 2010

Vapor Separator and Expansion Tank Hose

08/09/2010 – Replaced Vapor Separator hoses and added a new Drain Hose for the Radiator Expansion Tank.  I removed, cleaned and painted top of Radiator, Radiator Screen and Expansion Tank.  I also cleaned up some areas of the engine compartment, and greased the Bonnet Latch area.


Sunday, August 8, 2010

Clean Engine

I pushed the car outside and De-greased and Cleaned Engine.  The engine doesn’t look all that much better, but let's see if it helps eliminate some of the "smoking".   I turned the key and listened for Fuel Pump, it sounded OK.  I started engine.  I used 1st, 2nd and reverse gear as I drove it around the yard (not on a street yet).  The Clutch and Slave Cylinder appear to be doing fine.  Smoke started again from engine compartment, shut off motor after driving in reverse from outside cleaning to the garage.  I checked the Absorption Canister leaks, and it appears the hose tape repair did the job. (no leaking).  Cleaned trunk, repaired the trunck latch, and removed broken plates and lights from the rear of the car.  Noticed 2 broken hoses that connect to the Vapor Separator in the trunk, will replace.  Also need to replace the hose attached to the Expansion Tank for the radiator.  I ran the car several times for several minutes to heat it up.  I wanted to check the cooling fans.  Both are working, one might be running slow, but they keep engine at mid range temperature.  The "smoking" from the engine compartment appears to be decreasing.

Saturday, August 7, 2010

Rusted Clutch FlyWheel

I started today by bleeding the clutch lines.  I thought I might have a rusted Clutch Flywheel  So, I started the “B” while in gear.  The car jumped forward.  Restarted with clutch in, put in gear, released the clutch and the car moved forward.  The clutch seems to be working now.  Had to cut ignition before further gear tests due to smoke.  Again, it could be just burning off old oil, etc.  So, I thought it would be a good idea to buy some Engine Cleaner  to clean up the engine a bit, hopefully to eliminate some of the "smoking".  I also noticed the smell of gaosline.   The hoses around the Absorption Cannisters are leaking. it is all wet around cannisters.  I removed and repaired a couple of the hoses.  The car is not turning over and staring now, and I can’t hear fuel pump working.  I may have to purchase a new fuel pump.  One day at a time.  Getting close to safe running mode, I hope.


Friday, August 6, 2010

Install Rear Brake Pads and Cylinders

Today I installed the new Rear Brake Pads and Cylinders. I bled the Rear Brake Lines and adjusted both brakes.  I greased the Rear Hubs for the Wire Wheels, and installed wheels and tires on rear of car. 

I also checked right Front Brake Pads and Rotor, they looked good, no need to pull passenger side front.  The car is ready for an attempted startup to check for smoke and “free clutch flywheel”.  Keeping fingers crossed.


Thursday, August 5, 2010

Install Clutch Slave Cylinder

A few days ago I had ordered a new Clutch Slave Cylinder, Rear Brake Pads, and Rear Wheel Cylinder from RockAuto.com.  I chose to order from Rock Auto because they has a $15 rebate on the Brake Pads.

The new parts arrived in just two (2) days, and I was eager to get them all installed. 


I ran into a problem installing the new Clutch Slave Cylinder, the piston was not going in, I couldn't hook it to the clutch fork.  I wrote in to All Experts (allexperts.com) for a solution.  All Experts wrote back instructing me to force the piston in.  I removed the Clutch Slave, “forced” piston in, and re-installed.  Everything seemed to be OK.   But now I think the Clutch Flywheel is rusted (read something about that online).  I feel I need to dis-engaged “rusted flywheel” to get clutch properly bled and working.   

Monday, August 2, 2010

Check Brakes

I had read online to check the brakes and rear wheel cyclinders, they may have rusted and locked up over time.  So today I checked REAR BRAKE PADS and LINES, as well as, the EMERGENCY BRAKE.  Both will need new “Rear Wheel Cylinders”.  They were both rusted in a locked position, and when disassembled, pistons were locked.  Also, the rear brake pads could use replacement (about 2-3mm of pad remaining).  I also watched the John Twist (University Motors) video on the rear brakes for the MGB.  I cleaned up the wheel and remaining parts for re-installation.  I will order new Rear Brake Pads and Rear Wheel Cylinders. 

Wednesday, July 28, 2010

Check Clutch

I decided to today to check out the Clutch.  The Clutch pedal feels very flimsy. I added some clutch fluid and bled the CLUTCH line from Master to Slave.  No help.  I then removed CLUTCH SLAVE CYLINDER to inspect it.  When I removed the boot, bunch of crap fell out and I noticed the entire pump system is locked up.  After struggling with the components, I finally disassembled the slave cylinder.  I hope I didn't damage any of the components and slave.  I decided to just order a rebuild kit.  I had ordered catalogs from Moss Motors (mossmotors.com), and Victoria British (victoriabritish.com).   Some other online sites I found were englishparts.com, britishcarpartsco.com, rockauto.com, the bhive.com, usmgparts and others.    I felt I would need to compare pricing, as finances for the project are a concern.